UPVC Replacement Door Handles
Over time the handles on your doors will wear down and need to be changed. When replacing them, it is essential that the new handles match the exact dimensions of the old handle.
The three measurements you need to examine are the top screw position the lever and key hole dimensions. Use the size guide to assistance in this.
Inline Lever/Lever
A lever handle is a contemporary door handle designed to work with new or replacement doors. This kind door handle is offered in a variety of styles and finishes. A variety of manufacturers provide this handle, including Avocet ERA, Fullex, Hoppe, Mila, Millenco & Yale.
Fab and Fix Windsor Inline Sprung Lever Door Handle
The door handles of uPVC/Composite are constructed of durable materials and are ideal for multi point lock doors that require a strong design. The handles are inline and run from the same spindle and screw fixings so they are easily installed on doors made of uPVC/Composite, either new or old.
The handle can be positioned and angled to suit all users. The handle has been tested to 200,000 cycles, which helps to ensure the quality of the finish and the performance of the handle over time. The lever that is sprung can be reduced to accommodate more locks. This is useful for narrower doors where the cylinder is situated further back in the door. A shortened lever is also an excellent option for doors where the latch can be operated by a thumb turn on the inside.
Lever Pad
A Lever Pad upvc door handle operates differently to the lever type handles that are found on the majority of doors. These handle types can either work off one single spindle (inline) or independently from both sides using two offset spindles or inline (pad). They are typically employed on UPVC double-glazed doors and are available in a variety of variations and styles.
The handles have been tested to at least 200 000 cycles and are available in a variety of finishes like White and Silver, as well as Chrome & Gold. The finish meets BS EN 1670:2007 Grade 5 and is also resistant to corrosion, giving the handle a high degree of durability and performance for its intended use.
All of the UPVC lever pad designs come with the spindle and screws, allowing them to be fitted on a new or existing uPVC door. The backplate fixing centers of 211mm allow for a wider handle, which can often be a benefit in replacing a defective or worn multi point door lock mechanism. These handle levers have springs, which eliminate the issue of door handles that move out of horizontal position when not being used.
When choosing a replacement UPVC handle and spindle it is crucial to match the dimensions of the PZ on both the multipoint lock and the uPVC door. This measurement is often referred to as the "handle centre" or "cylinder centres which is a crucial aspect to match the appropriate handles.
Once you have decided on the correct PZ size it is important to ensure that the push and lever pads are shaped to fit the American with Disabilities Act compliant handles you require for your door. They typically have rectangular or round in design with an internal lever and an external push pad.
The majority of UPVC lever pads we sell are sprung, meaning that they will return to their horizontal position after not in use, instead of hanging out and potentially sticking in the frame. repairmywindowsanddoors helps prevent the draughts and cold air from getting into a house. The majority of UPVC lever pad handles come in both left and right handed models, allowing them to be put on either side of doors.
Euro Cylinder
Cylinder locks are found on uPVC and other types of doors. Cylinder locks are operated with a key that unlocks the cylinder's case. This reveals pins that can be aligned to the pins in the lock and allow them to rotate the revolving camera, thereby opening the door. Euro cylinders can be fitted with up to six pins. External and internal doors require different levels of security.
The choice of the correct cylinder is essential; it is contingent on the way your door and handle are utilized. For instance, doors that are external should be fitted with an extra secure cylinder, while internal doors can be secured using a standard cylinder. Some cylinders have extra features that can increase security, for instance, anti-drill or anti bump properties.
A euro cylinder must be measured accurately to ensure it is the correct size for your door. The cylinder should be measured from the hole in the center of the fixing screw to each end of the cylinder, including the thumb turn if you have one. If you cannot measure with the lock in position, you can remove it. A cylinder that protrudes beyond the handle and escutcheon may be vulnerable to attacks, such as snapping locks, therefore it is crucial that it is not too long.
Most modern cylinders are constructed with bump and anti-drill features included in their design. These are designed to reduce the chances of an attack by forcing the cylinder to rotate in the opposite direction. This will help to stop the attack and ensure your doors are secure.
There are cylinders that are designed to resist snapping. This is a common occurrence on cylinders. A specific tool is used to break the lock's break line and the front of the cylinder is snapped off. This is a much faster and easier way to gain access than a multipoint locking system. It also leaves no evidence of the break-in which can make it difficult to prove insurance claims.
Spring Cassette
The spring cassette is located in the base of your door handle's backplate, providing a spring solution and returning your multipoint lock handles to their rest position after using. There was a time when handles of this kind didn't have a spring built into them and without this they can droop or 'drop' once the locking mechanism is disengaged. This simple component is the most effective way to solve this issue. It also stops your door from becoming stuck in the open or closed position as they aren't easy to close manually.
These spring cassettes are specially designed for use with multipoint locks that are sprung, they will not fit non-sprung multipoint handles. You will need to have a hole specifically cut in the backplate to allow them to fit (please check the image for a technical diagram). These cassettes are a solution for damaged or missing cassettes on the backplate of uPVC door handles. They feature a square cut out which can accommodate an 8mm spindle, and are sold as a set.
These spring cassettes are a fantastic value for money solution to the issue of handles on your doors sliding. They are easy to fit and will extend the lifespan of your uPVC doors. For more information on our wide range of uPVC accessories and spares, contact us today. in touch with our team. We are always ready to offer expert advice and to assist you.